71102-T7M-H00 Front Right Fog Light Bezel for HONDA Crider 2019

71102-T7M-H00 Front Right Fog Light Bezel Product Overview

The product shown under 71102-T7M-H00 is a front right fog light bezel intended for HONDA Crider 2019. Check the right orientation, lamp opening, mounting tabs and standard-specification specification against the original component.

Fitment and Application for Crider

Before sourcing this front right fog light bezel, compare every fixing tab, inspect the lamp aperture size, and compare the original grille section. At the workshop preparation stage, inspect the removed bezel, confirm the vehicle market, and check the vehicle build date.

Before confirming this fog light bezel, compare the original grille section, review the bezel orientation, and confirm the surface finish. For a repeat wholesale order, check adjacent bumper parts, match the locating-slot layout, and compare the installation direction.

For HONDA Crider 2019, confirm the vehicle market, inspect the removed bezel, and compare the original grille section. While reviewing the supplied photographs, inspect the lamp aperture size, compare every fixing tab, and review the bezel orientation.

Front Right Fog Light Bezel Design and Replacement Notes

When separating nearby Crider variants, review locator direction, compare vent or grille openings, and inspect the frame width. During the physical comparison, check the lamp interface, compare transferred hardware, and inspect reinforcement ribs.

When comparing 71102-T7M-H00 with the removed bezel, compare the surface texture, check the adjoining gap, and inspect the back-side structure. When checking the bumper opening, compare mounting-hole height, confirm decorative finish details, and compare the original edge profile.

For the listed 2019 application, inspect the back-side structure, inspect the end geometry, and inspect the frame width. At the workshop preparation stage, inspect reinforcement ribs, inspect the moulded face, and measure the original length.

Application-Specific Identification Notes

Before workshop installation with 71102-T7M-H00 on the Crider 2019: check the vehicle build date. The HD02008-124 sample for the right side should compare vent or grille openings. For HONDA identification, 71102-T7M-H00 also requires technicians to support the bumper cover evenly. A buyer quoting HD02008-124 should include the complete OE reference for the HONDA Crider 2019 order.

For application-specific sourcing with 71102-T7M-H00 on the Crider 2019: compare the full OE marking. The HD02008-124 sample for the right side should inspect the moulded face. For HONDA identification, 71102-T7M-H00 also requires technicians to align the lamp opening first. A buyer quoting HD02008-124 should confirm sample requirements for the HONDA Crider 2019 order.

Before workshop installation with 71102-T7M-H00 on the Crider 2019: review market-version differences. The HD02008-124 sample for the right side should compare mounting-hole height. For HONDA identification, 71102-T7M-H00 also requires technicians to avoid bending moulded tabs. A buyer quoting HD02008-124 should retain the product label for the HONDA Crider 2019 order.

For application-specific sourcing with 71102-T7M-H00 on the Crider 2019: compare the full OE marking. The HD02008-124 sample for the right side should review fastening slots. For HONDA identification, 71102-T7M-H00 also requires technicians to check the final perimeter. A buyer quoting HD02008-124 should state the required quantity for the HONDA Crider 2019 order.

Installation Guidance

Before sourcing this front right fog light bezel, inspect each screw point, confirm the fitting direction, and protect exposed panel edges. While checking adjacent body parts, review separate hardware needs, check the final perimeter, and confirm an evenly seated fit.

Before confirming this fog light bezel, review the completed alignment, inspect damaged mounting points, and protect exposed panel edges. Before clips or hardware are transferred, support the bumper cover evenly, retain the removed bezel for comparison, and inspect the surrounding guides.

For HONDA Crider 2019, protect nearby painted surfaces, verify the lamp remains centred, and review the completed alignment. During the physical comparison, review separate hardware needs, inspect each screw point, and avoid bending moulded tabs.

Product Technical Specifications

Wholesale Supply and Packing

When separating nearby Crider variants, state the required quantity, support the bezel during transit, and compare the supplied photographs. Before packing the confirmed item, request protective inner wrapping, protect projecting locator tabs, and confirm separate clip requirements.

When comparing 71102-T7M-H00 with the removed bezel, protect projecting locator tabs, provide the delivery country, and confirm the packing method. For a no-force trial fit, confirm separate clip requirements, inspect receiving condition, and include the complete OE reference.

For the listed 2019 application, review carton edge protection, confirm separate clip requirements, and compare the supplied photographs. While checking adjacent body parts, check the ordered mounting side, state annual purchasing volume, and request export quotation terms.

Frequently Asked Questions

Can photographs alone confirm 71102-T7M-H00 fitment?

Photographs help with shape and finish comparison, but the OE number, vehicle year, side, trim specification and mounting geometry should also agree. For Crider, check the nearby lamp opening, check the adjoining gap, confirm the fitting direction, and check the ordered mounting side before installation or quotation.

Does trim specification matter for 71102-T7M-H00?

Yes. standard-specification can change the opening pattern, finish and locator positions, so compare the removed bezel and bumper before purchase. For Crider, review market-version differences, compare the original edge profile, trial-fit the bezel without force, and request supported carton packing before installation or quotation.

How should 71102-T7M-H00 be compared before installation?

Compare the complete OE number, outer contour, lamp opening, locating tabs, screw points and surface finish with the removed component before tightening hardware. For Crider, inspect the lamp aperture size, measure the original length, review separate hardware needs, and request export quotation terms before installation or quotation.

What should be inspected when 71102-T7M-H00 arrives?

Check the label, contour, surface finish, lamp aperture, tabs, mounting points and carton condition before installation or disposal of the packaging. For Crider, check adjacent bumper parts, check the bezel curvature, inspect damaged mounting points, and support the bezel during transit before installation or quotation.

Where is 71102-T7M-H00 installed?

The listed front right fog light bezel belongs in the right front bumper area. An opposite-side or different-trim bezel may use another outline and tab arrangement. For Crider, check the vehicle build date, check the lamp interface, confirm an evenly seated fit, and state the destination port before installation or quotation.

Request a Quote

Send the complete OE reference 71102-T7M-H00, vehicle details, mounting side, quantity and destination. Yongshang Auto can review the application before preparing a product-specific export quotation.