71102-T6P-H00 Front Right Fog Light Bezel for HONDA Crider 2013

71102-T6P-H00 Front Right Fog Light Bezel Product Overview

This product page presents 71102-T6P-H00 for buyers comparing a front right fog light bezel for HONDA Crider 2013. Check the right orientation, lamp opening, mounting tabs against the original component.

Fitment and Application for Crider

When preparing a Crider bumper repair, review market-version differences, compare the original grille section, and confirm the model year. Before final installation, match the outer contour, inspect the lamp aperture size, and confirm the bumper position.

During comparison with the original lamp surround, review facelift styling, confirm the bumper position, and check the nearby lamp opening. During receiving inspection, compare every fixing tab, inspect the removed bezel, and verify the mounting side.

For replacement in the right front area, check adjacent bumper parts, confirm the vehicle market, and confirm the model year. Before the quotation is confirmed, verify the mounting side, check the nearby lamp opening, and match the outer contour.

Front Right Fog Light Bezel Design and Replacement Notes

Before the removed bezel is discarded, inspect the end geometry, inspect the moulded face, and compare mounting-hole height. For a repeat wholesale order, compare transferred hardware, check the bumper transition, and review locator direction.

During an OE-led review for HD02008-112, check the adjoining gap, compare transferred hardware, and measure the original length. While reviewing the supplied photographs, inspect the back-side structure, check the lamp interface, and review nearby cover openings.

For wholesale selection of 71102-T6P-H00, compare mounting-hole height, compare the centre alignment, and measure the original length. Before final installation, inspect the moulded face, inspect reinforcement ribs, and inspect the frame width.

Application-Specific Identification Notes

For application-specific sourcing with 71102-T6P-H00 on the Crider 2013: review market-version differences. The HD02008-112 sample for the right side should inspect the end geometry. For HONDA identification, 71102-T6P-H00 also requires technicians to confirm an evenly seated fit. A buyer quoting HD02008-112 should support the bezel during transit for the HONDA Crider 2013 order.

For application-specific sourcing with 71102-T6P-H00 on the Crider 2013: match the locating-slot layout. The HD02008-112 sample for the right side should inspect the moulded face. For HONDA identification, 71102-T6P-H00 also requires technicians to protect exposed panel edges. A buyer quoting HD02008-112 should inspect receiving condition for the HONDA Crider 2013 order.

For application-specific sourcing with 71102-T6P-H00 on the Crider 2013: review market-version differences. The HD02008-112 sample for the right side should check the adjoining gap. For HONDA identification, 71102-T6P-H00 also requires technicians to confirm the fitting direction. A buyer quoting HD02008-112 should provide the delivery country for the HONDA Crider 2013 order.

For application-specific sourcing with 71102-T6P-H00 on the Crider 2013: verify the mounting side. The HD02008-112 sample for the right side should review nearby cover openings. For HONDA identification, 71102-T6P-H00 also requires technicians to protect exposed panel edges. A buyer quoting HD02008-112 should inspect receiving condition for the HONDA Crider 2013 order.

Installation Guidance

When preparing a Crider bumper repair, review separate hardware needs, protect exposed panel edges, and confirm the fitting direction. When checking the bumper opening, inspect each screw point, check lamp-to-bezel clearance, and retain the removed bezel for comparison.

During comparison with the original lamp surround, verify the lamp remains centred, transfer reusable clips carefully, and confirm the fitting direction. At the workshop preparation stage, confirm the finished bumper gap, inspect damaged mounting points, and inspect each screw point.

For replacement in the right front area, inspect damaged mounting points, clean the bumper mounting area, and confirm an evenly seated fit. For a repeat wholesale order, inspect each screw point, check adjacent panel gaps, and protect nearby painted surfaces.

Product Technical Specifications

Wholesale Supply and Packing

Before the removed bezel is discarded, include the complete OE reference, protect projecting locator tabs, and retain the product label. Before clips or hardware are transferred, review carton edge protection, check the ordered mounting side, and confirm the packing method.

During an OE-led review for HD02008-112, retain the product label, state the required quantity, and confirm separate clip requirements. During the physical comparison, confirm the required finish, request export quotation terms, and inspect receiving condition.

For wholesale selection of 71102-T6P-H00, check the ordered mounting side, compare the supplied photographs, and confirm separate clip requirements. When checking the bumper opening, review carton edge protection, state the target vehicle, and confirm sample requirements.

Frequently Asked Questions

Are mounting clips supplied with 71102-T6P-H00?

The supply scope follows the product photographs. Reusable clips, screws or separate brackets should be confirmed before the order is finalized. For Crider, review market-version differences, check the adjoining gap, support the bumper cover evenly, and confirm separate clip requirements before installation or quotation.

Does 71102-T6P-H00 include the complete lamp assembly?

No. This listing covers the pictured front right fog light bezel. The fog lamp, bulbs, wiring, switches and separate clips are not included unless they are visibly shown. For Crider, review market-version differences, compare mounting-hole height, check adjacent panel gaps, and state the destination port before installation or quotation.

How should 71102-T6P-H00 be protected for export?

The bezel should be supported inside the carton with its narrow edges, lamp opening and projecting tabs protected against compression, abrasion and impact. For Crider, review market-version differences, compare the original edge profile, confirm the fitting direction, and include the complete OE reference before installation or quotation.

What vehicle application is listed for 71102-T6P-H00?

71102-T6P-H00 is presented for HONDA Crider 2013. Confirm the full OE reference, model year, trim version and installation side against the removed part before ordering. For Crider, review market-version differences, check the bumper transition, inspect the surrounding guides, and retain the product label before installation or quotation.

Can photographs alone confirm 71102-T6P-H00 fitment?

Photographs help with shape and finish comparison, but the OE number, vehicle year, side, trim specification and mounting geometry should also agree. For Crider, review market-version differences, measure the original length, trial-fit the bezel without force, and check the ordered mounting side before installation or quotation.

Request a Quote

Send the complete OE reference 71102-T6P-H00, vehicle details, mounting side, quantity and destination. Yongshang Auto can review the application before preparing a product-specific export quotation.